Bildet die Brücke zwischen einer
Mediensteuerung mit Kontakteingängen
und dem Funkempfänger in der Leinwand.
Die Mediensteuerung wird direkt mit
den Kontakteingängen verbunden.
Die Steuerung der Leinwand erfolgt
dann über den eingebauten Funksender.
Für Diplomat Tab Tension und
Thor Tab Tension
für Diplomat Tab Tension und
Thor Tab Tension.
Pro Leinwand werden 2 Stück benötigt
For Descender (Large) Electrol, Elpro
Concept, Hapro manual,
length: 100 cm, can be shortened
For Compact Electrol, Compact Manual,
Pro Screen, Slim Screen,
length: 100 cm, can be shortened
Zur Montage der Leinwand z. B. in
abgehängten Decken.
Bestehend aus 4 Montagewinkeln, 4
Gewindestangen M8x100 sowie dem
notwendigen Befestigungsmaterial
For Elpro Large Electrol, length: 100
cm, can be shortened
For Descender Electrol, Elpro
Concept, Compact Electrol,
Hapro Manual, Pro Screen,
length: 75 cm
For Descender Electrol, Elpro
Concept, Compact Electrol,
Hapro manual, Compact Manual, Pro
Screen, length: 30 cm
For Descender Electrol, Elpro
Concept, Compact Electrol, Hapro
Manual, Compact Manual, Pro Screen,
length: 10 cm
For Slim Screen (not XL-Version)
Für Dolomit II / Scala II
Für Dolomit II / Scala II
Für Dolomit II / Scala II
Zur direkten Wandmontage der
Großbildleinwand
Zur Wandmontage der Großbildleinwand
Zur Wandmontage der Großbildleinwand
Set of wall clamps for all screens
For mounting Easy Install screens in
false ceilings
For all electrical screens and ceiling
lifts with wireless switch and mobile
sender, up to 30 m distance
230 VAC, 2-Pin for up/down,
on-wall mounting
230 VAC, 2-Pin for up/down,
on-wall mounting
Mit Rahmen Busch Jaeger Reflex Si,
alpinweiß,
Nennspannung: 250 V~,
Nennstrom: 10 A.
Nur in Verbindung mit handelsüblichen
UP-Gerätedosen nach DIN 49073.
Mit diesen Jalousieschaltern/-tastern
wird ein zu schnelles Umschalten der
Laufrichtung verhindert.
The Power Sensing Trigger will turn
every installation into an easy
control system. Usually a projector
needs to have a 12 volt trigger output
to send the projection screen a signal
to unroll when the system is turned
on. Not every projector however has
this trigger output, but the Projecta
Power Sensing trigger will now give
every projection system that
functionality.
The Power Sensing trigger will be
connected in between the power source
and the projector. When the projector
is turned on, the trigger senses power
going to the projector and signal the
projection screen to unroll. When the
power is switched of the trigger will
signal the projection screen to
retract again.
Plug & play with receiver, 4-channel
remote, 5 m power cable with mains
plug, range up to 30 m
EasyInstall (5944000011) to control
screens,
frequency 868,3 Mhz
Plug & play with receiver, remote,
5 m power cable with mains plug
range up to 7 m
Control of a screen/ceiling lift in
2-stop position via a media control
and a low voltage relay. Power supply
12 V DC / 0,2 A additionally required
Plug & play, for controlling screens
via relay output of a media control,
5 m power cable with mains plug
Pull rod for all manual screens
125 cm
For Tripod screens
Pro View and Picture King
For Tripod Screens for
Pro View and Picture King
For Tripod Screens for
Pro View and Picture King
For Tripod Screens for
Pro View and Picture King